Sample Preparation

Typically, titanium and zirconium samples are chemically etched to remove surface contamination when oxygen and nitrogen are determined. However, etching can introduce hydrogen into the sample.

ASTM method E 1409 "Determination of Oxygen and Nitrogen in Titanium and Titanium Alloys by the Inert

Gas Fusion Technique", as updated in 1996, permits either etching or abrading (filing) of the test specimen.

ASTM E 1447 "Determination of Hydrogen in Titanium and Titanium Alloys by the Inert Gas Fusion Thermal

Conductivity/Infrared Detection Method" permits surface preparation by abrading (if necessary to remove

contamination). Differences in sample preparation present somewhat of a dilemma regarding simultaneous

determination of O, N, and H in titanium. However, abrading samples with a file to remove surface

contamination will yield accurate O, N, and H results. The ONH836 utilizes a high-power electrode furnace to quickly and efficiently release the target gases from within the sample, which allows for a very rapid simultaneous determination of oxygen, nitrogen, and hydrogen.

氧氮氢分析仪的常见故障及解决方法

供电正常、通讯正常，点击确认键后分析仪不工作。这是没有水流，炉子温度太高或仪器通道电压不正常。如没有水流，炉子温度太高这些信息会显示在显示器画面上，但没有信息显示说明这两项正常。接下来检查仪器通道零位电压，如果比±3V高出1V以上，可能是因为气瓶空了，或者是空气进入到分析仪中。检查并更换化学试剂，如果有空气进入热导池里，热导池的电压就会＜-6V，此时打开右面的门，堵住炉子气体进口，10s后，热导池电压值必然升高。经过逐一排查，**终确认碱石棉有问题，更换后仪器正常。 上海分析仪全自动分析系统、打印机、天平、远程诊断。

Procedure – Powder/Chip Samples

Determine the instrument blank.

Press the Analyze button on the instrument screen, the lower electrode will close and the analysis sequence will start and end automatically.

Repeat steps 2b through 2g a minimum of three times.

Set the blank following the procedure outlined in the operator's instruction manual.

Instrument calibration/drift correction.

Login a minimum of three Standard reps.

Weigh approximately *** grams of a calibration/drift standard into a *** Nickel Capsule; enter the mass and standard identification into appropriate rep fields. If applicable, place the nickel capsule in the appropriate autoloader position.

Instrument Highlights and Features

Optional Features

Optional boom-mounted touch-screen interface package (M) promotes an ergonomic workspace

Optional Performance Package (P) adds a three-stage carrier gas purification system, and a dual-loop gas dose module

Optional Dual Cooling Package (D) adds an integratedliquid-to-air radiator with dual cooling fans. This DC

option gives the user the choice of liquid-to-liquid cooling, liquid-to-air cooling, or a combination of both

Optional integrated autocleaner (H) automatically cleans the upper electrode and lower electrode tip

Optional 20-sample shuttle loader available

试样加载过程中完全密闭，消除大气的中可能带来的杂质的污染。

Instrument calibration/drift correction.

a. Login a minimum of 3 Standard replicates.

b. Weigh a ~1.000 gram of a calibration/drift standard, enter the mass and standard identification into appropriate replicate fields.

c. Press the Analyze button on the instrument screen. After a short delay, the loading head slide-block will open.

d. Place the calibration/drift standard into the open port at the top of the loading head.

e. Press the Analyze button on the instrument screen again, the loading head slide-block will close and the lower electrode will open.

稳固的炉头试样加载结构。新疆美国LECO分析仪咨询报价

上海禹重给您提供各种氧氮氢分析仪，欢迎来电咨询！安徽专业元素分析仪

氧氮氢分析仪的操作过程

氧氮氢分析仪可根据的用户的要求定制。该分析仪配备两个不同灵敏度的探测器，在更多的应用中保证了准确度。

操作简单而且安全。在样品称重以后，样品的重量数据通过电子界面传导至相连的电脑中，也可以在软件界面中手动输入样品的重量。

样品被放置在水平放置的炉子中的低温区域。分析开始以后，炉子开始向上转动，然后样品逐渐落入加热区。通过添加载体气体氮气，氢气被扩散出来并且随载体被传导至一个高灵敏度的热传导测量池。

通常一次测量的时间在3到15分钟之间。在分析的过程中设备可以显示测试信号和设备的参数，从信号的评估到结果在界面上的显示全部自动完成；而测量数据则被传导至LIMS（实验室信息管理系统）中。无需过多的保养和维护，而除尘器和净化管的维护工作也方便。