company profile

Shanghai Uzong Industrial Co., Ltd. (hereinafter referred to as UZONGLAB®) is a high-tech company that provides integrated solutions for intelligent laboratories, mainly serving the Chinese market and countries along the “Belt and Road”. It has three business divisions and one The technology center, namely the instrument business department, consumables business department, project development department, and Zhongyu Lianhe Technology Center. In addition to the Shanghai headquarters, we have established branches in Beijing, Shenyang, Shijiazhuang, Taiyuan, Qingdao, Guangzhou, Chengdu and Urumqi. To provide customers with more professional, safer and more convenient products and services is our sole goal. 可选具有压力补偿和温度控制性能的标气检测气路。北京进口分析仪哪家好

Oxygen, Nitrogen, and Hydrogen in Refractory Metals

Summary

One of the most critical chemical specifications of titanium alloys is the hydrogen content. Too high of a

hydrogen content can cause hydrides to precipitate, which can lead to embrittlement and subsequent

cracking when the alloy is stressed. Hydrogen pickup typically occurs during downstream processing steps

such as heat treating, pickling, and cleaning.

The LECO ONH836 is a simultaneous oxygen, nitrogen, and hydrogen determinator that utilizes an electrode furnace, inert carrier gas, and both infrared and thermal conductivity detection to meet the analytical needs of the refractory metal industry. 

This application note was written specifically for use with the LECO ONH836 series determinator.

Instrument calibration/drift correction.

a. Login a minimum of 3 Standard replicates.

b. Weigh a ~1.000 gram of a calibration/drift standard, enter the mass and standard identification into appropriate replicate fields.

c. Press the Analyze button on the instrument screen. After a short delay, the loading head slide-block will open.

d. Place the calibration/drift standard into the open port at the top of the loading head.

e. Press the Analyze button on the instrument screen again, the loading head slide-block will close and the lower electrode will open.

氧氮氢分析仪的常见故障及解决方法

仪器启动时显示。没有水流。系统分析电流切断，分析停止。这是水流探测器不正常，水泵不工作，管道堵塞。将仪器的右面板取下，观察水流探测器，用手挤压补水塑料水瓶，发现水流正常，显示正常，证明水流探测器正常，管道畅通。启动循环水泵，但分析仪显示没有水流，此时可判定水泵不正常。打开水泵转子密封口，启动泵发现电机正常运转，此时关闭进水，拆下水泵，发现叶轮脱落。经了解，判定是由于外部冷却水停水，仪器内循环水温过高（水温应≤70℃），致使叶轮（叶轮材料PVC）热胀并脱轴。用粘合剂粘合叶轮后再粘于叶轮轴上，待粘合剂凝固后试车，仪器运行正常。 ***触摸屏技术，用户友好界面软件进行校正、分析、诊断等。

氧氮氢分析仪的常见故障及解决方法：

氧和氮空白值超过20。这是由于气流小，不能将炉子中的空气驱赶出去。可调节气体流量，调节载气压力在0.2~0.4MPa。接通仪器载气，放一个石墨坩埚在下电极上，打开主电源开关，点击软件上的关炉按钮，关闭炉子并等待10s。调节流量调节器，直到流量计a显示为30L／h，打开炉子。调节调节器直到流量计b显示为50L／h，再次关闭炉子。如果以上设置不稳定，则增加流量至100L／h，反复调节直至仪器稳定。 氧氮氢分析仪选哪家？给您推荐上海禹重！湖南美国分析仪供应商

**的动态流量补偿（DFC）保证热导池气体流量、压力恒定。北京进口分析仪哪家好

力可ONH836氧氮氢分析仪

特征

稳固的炉头试样加载结构

试样加载过程中完全密闭，消除大气的中可能带来的杂质的污染；

简化日常分析所需的炉头进样部分机械维护工作。

可选的自动功能

上下电极自动清扫装置；

20位试样及坩埚自动进样装置。

附加功能及优点

可选六轴可旋转触摸屏幕，增强了操作的工效和直观性；

可选具有压力补偿和温度控制性能的标气检测气路；

新型气路管道减少气路连接阀，使得漏气，断路故障更少；

配置SmartLine Remote远程诊断功能。

北京进口分析仪哪家好